Hotronic Ski Boot Heaters Guide
Table of Contents:
Installing Heating Elements on Custom Insoles
Installing Your Heating Elements in Your Hotronic Heat Ready Insole
Installing Hotronics in General Footwear
Slide Strap vs. Strap Bracket
How to Mount and Install Your Strap or Slide-Strap Brackets
Attaching Your Battery Packs to Your Slide Strap or Strap Bracket
Turning Hotronic Batteries On and Off
How to Recharge your Hotronic Battery Pack
What to Expect from your Hotronic Battery Packs
Hotronic Summer Storage
General Tips for Using Hotronics
Hotronic Battery Pack Compatibility
How to tell your Hotronic Production Year
What are Hotronics?
We love skiing, but we understand that sometimes the cold weather can freeze your feet and limit your skiing enjoyment. You can shake an adhesive foot warmer pack and try to smooth it out in your boot, but then you’re left with a bulky pack that will lose its warmth before your ski day is done. Luckily, Hotronic foot warmers are an easy way to fix this issue!
Hotronic’s are a popular battery powered ski boot heater. Heated gear is every skier’s dream, and now, it’s finally affordable too! When you add Hotronic heat-ready inserts to your ski boots, your feet stay warmer so you can have fun on the slopes all day long. Hotronic battery powered boot heaters work while you’re skiing. Just slip the insert directly into you ski boot, and enjoy hours of toasty warm tootsies. When you aren’t skiing, you can plug in your battery pack and completely charge it in 3 hours or less. These heated inserts work in any type of shoe or boot, not just ski boots, and they last for years. Forget about cold feet, and get your family some heated shoe inserts from Hotronic, available through Utah Ski Gear. If you are looking for a part or accessory and don’t see it on our web site, let us know. We will contact Hotronic on your behalf and try to get it for you.
WONDERING WHICH HOTRONIC TO GET? TAKE OUR LITTLE QUIZ BELOW TO FIND OUT!
Once you’ve invested in custom ski boot footbeds and Hotronic foot-warmers, it is important to install them correctly. As long as you follow a few basic guidelines, your Hotronic heating elements can be installed swiftly and easily. If you have custom footbeds then you will need the Hotronic Custom Kit.
First, step on your custom insole and place your heating element under your toes with the power cord pointing towards the heel. Remove your foot and carefully lift the heating element enough to make a small mark on the insole- where the bottom of the element ends and the power cord starts. Then use a razor knife or grinding device to make a slit or narrow opening at the marked position. The slit should be large enough for the black plug to go through. If your insole is made of harder material, you will have to cut a larger slit for the plug to go through, as you cannot bend your insole. Although it may seem counterintuitive to slit your footbed, it is required to properly install your heating elements. Once your slit is made, run the power cord through the opening until the heating element lies flat in the correct position. Your power cord should now be under the insole, while the element is on top of the insole.
You can then remove the adhesive cover layer from the bottom of the element and place it in the correct position on your custom insole. Next, apply the self-adhesive fabric cover or ‘cambrelle’ over the top of the insole and heating element. Trim any excess adhesive fabric with scissors so that it matches the outline of your custom insole. Lastly, apply the self- adhesive fabric strip over the power cord that is under the insole. This will allow the power cord to stay in place.
Once the heating element is attached to your insole, you must install it in your ski boot. To do this, cut another small T Slit in the liner so that the power cord can go through the liner. You can then use any extra adhesive fabric or another form of tape to attach the power cord to the outside of the liner. This will help keep the power cord in place in your ski boots.
Installing the Heating Elements
When you initially receive your Hotronic heating elements you may feel overwhelmed by the idea of installing them yourself. Luckily for you, Hotronic Universal Kit makes it extremely easy for you to install your boot heaters at home. First, open up the flap on the bottom of your heat ready insole. Remove the adhesive backing and attach the heating element to the designated and cut out area. The power cord should be facing up and aligned with the divot intended for the power cord. Next, remove the adhesive cover layer from the heating element. Close the door flap and firmly press each side of the insole. Once the heating element has been inserted into the Heat Ready insole, trim the insole to the correct boot size.
Trimming Your Insoles
If you are using Hotronic’s ‘One Size Fits All’ Heat Ready Insole that comes with the Universal package, align the tips Hotronic insole with the original boot insole. Then, trace the original removable insole on the backside of the Heat Ready insole. You can then use an Exacto- knife or razor to trim the edges of the Hotronic insole.
If you decide to the use Hotronic’s ‘Custom Insoles’, you must first choose the best size insole for your ski boot. There are four metric sizes to choose from, 23.5/24.5, 25.5/26.5, 27.5/28.5, 29.5/30.5, but if your boot is smaller than this you can trim the insole to fit by following the directions for the ‘One Size Fits All’ insoles. If your custom insole fits well inside your boot, you do not need further trim it. However, if it does not then use the trim-to-size lines that are printed on the bottom side of the insole.
Make sure to avoid cutting the power cord and heating element when you are trimming the insoles as this will defect your product. It is also important to place the red fabric side of the insole up in the boot, as this is the top of the insole and should be next to your foot.
You don’t have to be skiing or snowboarding to enjoy the warmth of Hotronic Elements. Hotronic’s can also be worn in your general footwear, meaning your toes can stay warm regardless of your activity. While activities like snowshoeing may initially come to mind, Hotronic’s can also be installed in your horseback riding boots, bike shoes, or fishing waders. You can also use them in your snow boots for the extra cold days spent doing errands around town. While you don’t need to use a Hotronic insole to use your elements, you may decide that using the insoles provides more comfort. However, some footwear may not have removable insoles that allow the element to be placed under them. If this is the case then you can install your heating elements with a Hotronic insole. Any of the Hotronic insoles work in general footwear so your choice will likely be dependent on comfort and shape of the shoe.
Installing Hotronic heating elements into your general footwear is very similar to installing them in your ski or snowboard boots.
- First, place the heating element under the insole of the footwear. Make sure the power cord is flat so that it doesn’t create any discomfort.
- Then, run the power cord up the side or back of the leg.
- Securely fasten the battery pack to the back or side of the footwear.
- Plug the power cord into the battery pack and you are ready to go!
If your footwear is smaller, such as a bike shoe then you may want to purchase extension cords and attach the battery somewhere on the waist. It is recommended that you place the batteries either on the back of your footwear or on the outside in order to reduce the chance of it being hit and falling off.
Both the slide strap bracket and the strap bracket are mounting brackets that better helps secure your Hotronic batteries. In order to use the slide strap bracket, you must remove the stock metal clip that comes with the battery. Because of this, it can be hard to transfer the batteries from boot to boot. If you are going to be using the Hotronic batteries on multiple boots, then it may be best to get the strap bracket. If you are only using the batteries on one pair of boots then the slide strap bracket is easier to maneuver and use.
Hotronic Slide Strap Bracket vs. Strap Bracket:
Pros: Secures Hotronic battery on to the boot power strap, easy to use
Cons: Can only use Hotronic battery on one set of boots
Pros: Secures Hotronic battery on to the boot power strap, can use the Hotronic battery on multiple pairs of boots
Cons: Harder to use
A slide strap bracket or strap bracket will make it easier for you to quickly attach and remove your Hotronic batteries. Mounting brackets also will keep your batteries more secure on your boot, so you don’t have to worry as much about losing your batteries. This is especially important if you are an aggressive skier, like moguls, or will be carrying your gear for longer periods of time.
To mount your Slide Strap or Strap bracket
- Determine the best location to mount the bracket on your power strap
- Too far forward will obstruct closer of power strap
- Too far back conflict with the top back spoiler of boot.
- If you are using a slide strap bracket then remove the preinstalled wire clip and locking plate that comes with your Hotronic batteries.
- You will need to aggressively push the plastic locking plate away from you in order to release it.
- You can then squeeze the metal clip together and out of the battery.
- Store this in case you would like to use it in the future
- Insert the wire form into the ends of the bracket
- The horizontal section should be on the backside of the power strap
- To secure the bracket, push the horizontal section of wire form over the center section of the strap bracket until the power strap is tightly in place between the bracket and wire form.
Using a Hotronic strap bracket helps keep your battery pack better secured to your ski boot. They are also relatively simple to use.
Attaching Battery Pack to Strap Bracket
- Position the battery pack horizontally so that the Battery Clip wire form slides over the top edge of the bracket
- Slide the battery pack down on the bracket firmly until the lower wire section of the battery clip snaps into place over the bottom edge of the bracket
- Turn the battery pack 90 Degrees so that it is in a vertical position
Removing Battery Pack from Strap Bracket
- Turn the battery pack 90 degrees into a horizontal position
- Push the battery pack down and pull out the lower wire form section of the clip until it releases from the lower edge of bracket
- Slide the battery pack up and off the strap bracket
A slide strap bracket makes Hotronic batteries more convenient and accessible to you, while also securing the batteries to your boot. A Hotronic slide strap bracket is a popular addition to foot warmer purchases because it helps prevent the battery from unclipping from the boot and falling off while skiing.
Slide Strap Bracket
Attaching Battery Pack to Slide Strap Bracket
- Place the battery pack wire clip channel over the top of the strap bracket
- Slide the battery pack down over the bracket until it snaps into position
Removing Battery Pack from Slide Strap Bracket
- Press together the flexible legs that are on the bottom of the bottom of the battery pack
- Lift the battery pack up and of the slide strap bracket
- To turn ON
- Press and hold the ON button until the LED light turns on.
- The light will either glow green or red
- To turn OFF
- Press and hold the OFF button until the LED light turns off completely
- This can take up to 5 seconds
- To change settings
- Press and hold the ON button to turn the level up
- An additional LED square will light up
- Press and hold the OFF button to decrease the level
- You will notice this change of setting in the LED lights.
- S4 and S3 batteries operate the same
- Press and hold the ON button to turn the level up
- Press and hold the OFF button until the LED light turns off completely
- Press and hold the ON button until the LED light turns on.
- Turning your Hotronic batteries on and off
Your Hotronic batteries should be recharged every night after you ski. Charging them promptly after use will help keep them conditioned and ready to use. If you are going a week or longer without skiing, it will be best to also charge your batteries the night before you go skiing or snowboarding in order to maximize the charge while you’re on the hill. The battery packs should not take longer than three hours to fully recharge. However, if your boot batteries are not properly conditioned, your batteries cannot reach their full temperature or duration potential. It is recommended that you turn off your battery pack before you start charging it. This means that all of the LED lights are off as well. Your Hotronic battery pack will still charge if it is left on, but changing the level setting on it can cause the charging process to stop.
When you’re ready to start charging your heating system batteries, plug the recharger into the wall outlet using the correct plug adapter (North American, European, Other). The recharger accepts electric input ranging from 100-240VAC. 50-60Hz and hotel room razor outlets are not recommended.The recharger will perform a short self-test with a brief red LED followed by a green LED, and then the LED will shut off. The recharger is then ready for you to attach the battery packs.
The LED on the recharger will remain red while the batteries are charging. If it starts flashing red, the recharger and battery are not compatible or there is an issue with the battery itself. The LED light on the recharger will turn green once one or more of the batteries are fully charged. One of the batteries may fully charge before the other so it may be a good idea to leave the battery packs on the recharger for a while after the LED glows green. Once the battery charging process is complete, you should unplug the battery from the recharger as well as remove the recharger from the wall outlet. This will help maximize the charge after recharging. It is recommended that you occasionally fully drain the batteries before charging them to maintain optimal strength.
You can unplug and reattach the battery pack at any time during charging. It can also be beneficial to occasionally fully discharge the batteries before recharging as this can help maintain optimal strength. It is also possible to only recharge one battery, rather than both batteries in the pack. Additionally, you can recharge differing Hotronic batteries on the same charger at the same time. After you have completed your recharging process, you are ready to hit the slopes!
If you’re new to electronic footwarmers, you may not know what to expect out of your Hotronic heating system. While each system may differ slightly, there are a few common things that occur universally with boot heaters.
- Newer Hotronic battery packs perform more optimally and all battery types eventually lose strength over time.
- Your batteries perform the best shortly after charging. Meaning, charge your battery pack shortly before using them.
- Unconditioned battery packs produce lower temperatures for a shorter duration. You should condition your batteries if they are new or have been unused for more than 2 months.
- Your battery will decrease in power if it is left on, even if it is unplugged from the power cord.
- Your batteries will self-discharge at a rate of 2 -5% a month.
- The battery will discharge at a faster rate if it is on a higher setting. Meaning, they will have a longer battery life if left on a setting such as one or two, rather than three or four.
- Your Batteries will not last as long in extremely cold weather.
- Expect imperceptible heat in your boots, rather than fireplace warmth.
It is important to remember these factors when using and caring for your Hotronic footwarmer batteries and elements. Taking them into consideration will help keep your batteries well maintained and your feet warm.
As the snow on the ground melts and the weather warms up, you’ll likely be putting away your winter gear, including your Hotronic heating system. While you’re not using your batteries and heating elements, it is still important to properly take care of them in order to ensure maximum functionality the next time you use them. You can keep your heating elements and power cord inside your ski or snowboard boots, but make sure that you store your boots in a dry environment to avoid any rust or mildew growing inside the liner that could affect the overall performance of the boot. Before you store your batteries, make sure to recharge them. When recharging, turn the battery pack off prior to plugging it in.
The charging process should then take about three hours or less. Remove the batteries from the charger before storing them and store them unattached from the heating elements as well. Do not store the batteries below 32 degrees or above 105 degrees, as this will harm the batteries. When you’re ready to begin using your heating system again, perform a battery pack conditioning charge for 24 to 72 hours uninterrupted. This will allow for a fuller charge and keep your feet warm for a longer amount of time. You’re now ready to tackle the cold weather!
Be careful getting on or off the chairlift. If the chairlift hits your boot warmer it can cause damage.
Take care walking down the stairs as the battery packs can catch the stair edge if they are mounted on the back.
Keep your boots and socks dry to avoid excessive heat loss
Condition your boot batteries to maximize their duration and temperature potential
Turn your foot warmers on before entering the cold to maintain warmth
Do not place another insole on top of the Hotronic insole
How do I know which series my Hotronic Batteries are?
Sometimes you may have a hard time distinguishing which battery series your Hotronic batteries are. Knowing which series your batteries are is important for determining which charger you can use. If you do not know which Hotronic battery series you have, the following descriptions may help.
Power Plus S Series/e series
- All batteries manufactured after 2006 are compatible with the same white charger. The e and S series have white ‘On’ and ‘Off’ buttons on the top. The rest of the battery will also be white and the top will be black. The model will be printed on the front of the battery, as with all of the models.
Power Plus m Series
- This Power Plus m series is the first Hotronic battery to be compatible with the white plug charger. Although very similar to both the e and S series, it is very light gray in color. Additionally, the ‘On’ and ‘Off’ buttons are yellow, rather than white.
Power Plus 3.5 Series
- The 3.5 Series was in production between the years 2003-2005 and is compatible with the blue plug charger. The batteries are light gray and have a black top. The level adjustment switch is blue to designate that it works with the blue plug charger.
Power Plus 2.7 Series
- Power Plus 2.7 was in production from 2004-2005 and is compatible with the red plug charger. It looks similar to the Power Plus 3.5, but the level adjustment is red to show that is works with the red plug charger.
Power Plus 2.5 Series
- The Power Plus 2.5 Series was only in production during 2003 and is also light gray. However, the level notch is in the center, rather than the side. It is also black, rather than color specific to the charger it is compatible with. However, it is also compatible with the red plug charger along with the Power Plus 3.5 and Original Power Plus.
Original Power Plus Series
- The original power plus series was in production during the years 2000-2002. It has a similar shape to the Power Plus 2.5, but is black with ‘Power Plus’ written on it. This battery series is compatible with the red plug charger.
Hotronic NiCad Series Battery
- The Hotronic NiCad series is the original Hotronic Footwarmer battery. It is predominantly black, with a little bit of yellow and red graphics on it. This series can be used with both the red plug charger and the dark grey plug. However, the dark gray plug cannot be used with any of the Power Plus battery packs.
On the bottom of your Hotronic battery, there will be two clock type circles of numbers. The first one will have 12 numbers on it, with an arrow pointing to one number. This number will coincide with the month that the battery was manufactured in. The second circle has fewer numbers and dictates which year the Hotronic battery was manufactured in. Typically it is common for every battery within a production year to have the same production month as well, but this is not always the case.
The production year on the Hotronics is a little harder to find, but still very simple. The second line on the back of the recharger includes the model number, which includes the production year at the end.
The production date on the heating elements is printed on the lower part of the black grommet. At the base of the plug will be a two digit number that correlates with the last two digits of the year that the heating element was produced.
At the bottom of the SnapDry there is a small engrained bow with product information. Within this box is a 3 digit code, which corresponds with the year that the SnapDry was manufactured. 2017 was the last year that Hotronic manufactured the Snapdry.
2005: 538 2011: 125
2006: 629 2012: 226
2007: 728 2013: 328
2008: 831 2014: 425
2009: 928 2015: 531
2010: 026 2016: 628
XLP Series- XLP One
These batteries have their production year printed on the bottom. Just as the Foot warmer batteries have a clock style circle with numbers, the XLP Series batteries do as well. There is only one circle on these batteries and the arrow will point to the correlating production year.
XLP Series Recharger
The production date on the XLP Series recharger is located directly under the plug adapter. There is a 3 number code that marks the year.
2016 Rechargers: 634
2017 Rechargers: 727
XLP Series- Heat Sock
The production date on the Hotronic Heat Socks is located on the inside of the cuff. Just below the three snaps is a small copyright symbol with a date after. This date directly corresponds with the year that the sock was manufactured.
Hotronic foot warmers a very durable product, designed to withstand cold outdoor conditions. However, in the case that any of your Hotronic items become defective, Hotronic provides a 2-year limited warranty for all of their S Series foot warmer products. In addition to our satisfaction guarantee, Utah Ski Gear is an authorized Hotronic dealer and the Hotronic limited warranty extends to all purchases made through Utah Ski Gear. The two-year timeframe begins at the time of purchase, and a dated proof of purchase is required for any warranty item. The limited warranty is still valid if you purchase your Hotronic items through a third party vendor such as eBay or Amazon. For any foot warmer from the 2014 production year or earlier requires a proof of purchase within the last 2 years.
The limited warranty does not cover damage relating to misuse, neglect, abuse, inconsistent use with operating instructions, normal wear, and tear, changes in exterior appearance, improper dealer service, improper dealer or consumer modifications to the product, or loss of product due to improper attachment. The warranty does not extend to variations in the heating element temperature and duration of charge due to improper charging. If you find a defect in your Hotronic batteries, heating element, or accessory, please return it to Utah Ski Gear immediately for replacement or repair.